SW-020-CN-B1 airsoft rifle
Small arms in the bull-pup (sometimes referred to as stockless) configuration have a long tradition and just as many supporters as sceptics. One of the advantages of this type of design, however, is hard to dispute - the possibility of using a really long and effective barrel, while maintaining the relatively compact dimensions of the carbine itself. The aesthetic qualities should not be forgotten either - bullpups are simply distinctive and cannot be mistaken for anything else.
As in the flammable original, the body of the replica was made of strong polymer polymer. Metal was used for the entire front part of the replica, as well as small elements such as the flap of the shell ejector or the flame suppressor.
In both the rear and front parts of the replica there are metal mounts for attaching the tactical sling. The adjustment knob of the hop up system can be accessed in the standard way, by pulling back the reloading handle and thus exposing the shell ejector window. The handle can be locked in the rear position. What is characteristic for this design, the ejector windows are located on both sides, so the left-handed user will also have comfortable access. The replica is finished with a long barrel with a large, "tank-like" discharge device.
The replica's battery is located inside the stock (if we can use this word in connection with the - nomen omen - stockless system). To do this, it is sufficient to remove the rubber boot. No tools are required for this, as it is attached "by pressing in". It also takes a few seconds to disassemble the entire carbine into two parts - if, for example, we want to access the hop-up chamber and the inner barrel. To do so, all you need to do is to press the metal pin - the locking mechanism - and slide out the fire selector, after which the structure is split into 2 parts - the body and the front part and barrel.
The replica has a total of 4 22mm RIS mounting rails on the back, sides and under the barrel.
The carbine has a two-stage trigger assembly, a shallower press of which produces a single shot, while a deeper press produces continuous fire. The safety is located at the pistol grip and can be operated on both sides.
The replica is equipped with a quick-change spring system, which allows the mainspring to be replaced with minimal time. There is no need to remove the gearbox and disassemble the entire structure: simply remove the buttstock, unscrew the polymer cap, and then remove the guide bar and spring through the hole in the rear wall of the gearbox.the system allows quick and efficient adjustment of the replica's power to the conditions expected on the airsoft battlefield, without the need for access to a workshop or a range of specialised tools. We can now easily guarantee the ideal compromise between the effectiveness of fire and the safety of ourselves and other players.
The replica comes with a polymer hi-cap magazine with a capacity of 330 BBs.
The kit does not include a battery or charger.
The kit includes:
- replica
- magazine
- instruction manual
Battery included NiCd
rechargeable battery is characterized by high efficiency
current-carrying capacity, but there are disruptive effect on memory.
Should be unloaded and loaded in the full cycle, ie, it is recommended
to fully discharge, and after unloading must charge the battery
immediately without leaving it for a long time in a discharged state. | No |
| Blow Back Blow back is a simulation system of the cocking lever - it imitates the work of it as the equivalent sharp. This system raises the realism and adds a lot more experience during shooting. | No |
| Colour | Olive |
| Product length [cm] | 99 |
| Product weight [g] | 4260 |
| Power supply | Electric |
| Material | Metal Plastic |
| Muzzle velocity [FPS] It is the spped of bb, while its leaving the innerbarrel of replica. This speed is measured in FPS (Feet Per Second). 1 FPS = 0,3 m/s 1 J = 99 m/s 1 J = 326,7 FPS | 400 |
| Fire mode | Full-auto Semi-auto |
| Gearbox version Indications v2, v3, v6 does not mean the level of advance, but only shape of gearbox skeleton which was used and selected by the manufacturer depending on the capabilities of the body of the replica. For example, a models of the M4/M16 family, MP5, have a v2 gearbox, while the AK family have gearbox v3. | Gearbox v3 modified |