CM013 carbine replica (ASCU version)
The newest series of the American assault rifles’ replicas which is made by the CYMA company. The replica characterizes itself with the quality offered for a reasonable price which is known from the other product of this manufacturer.
The make is fully compatible with the Tokyo Marui standard, the replicas are equipped with metal hop-up chamber and the M110 type main springs which guarantee the muzzle velocity of about 370 FPS what makes them a highly efficient tool to operate on middle distances.
The particular parts of the replica are made in a way guarantying a proper fitting of the inner parts and the placement of the electronic and mechanical elements of the outer construction.
The replica is made of metal and - mostly - plastic. The use of the metal gearbox in the replica ensures an extended operation than in the case of the fully plastic equivalents. Thanks to the metal gearboxes, the replica can be highly modified in order to improve the replica’s power.
The application of the foldable stock allows the adjustment of the replica to almost every user and the use of the replica in all situations and conditions. Thanks to the applications of the 22mm RIS rail on the top of the replica, it is possible to mount a red dot sight or a scope.
The carbine has got an adjustable hop-up system to which we gain access by pulling the cocking handle and which opens the dust cover which hides the adjustment knob. The battery is located in the stock's pipe.
The ASCU is a two-part electronic module ( the control module and the sensor module ) which, upon being installed in the Airsoft replicas, significantly improve their operation. The traditional joint module was replaced with a sensor module which monitors the actual position of the piston thread-wheel, the firing mode selector lever and the trigger. The gathered information is sent to the control module – in which the software located in the processor analyzes it and controls the replica’s motor with the use of the MOSFET active break.
ASCU Gen. 3+ includes the following upgrades:
- added polymer padding to the circuit boards, protecting them from damage during installation
- obsolete short-circuit software removed, making shots in semi-auto much faster
- a dedicated H-U chamber makes it impossible to shoot when the magazine is empty
- every pull on the trigger results in a single shot, new system prevents any double-shots
- new cut-off lever and selector plate designed specially for the ASCU
- new, thicker wires
- no need to dremel or modify the reinforced gearboxes.
The ASCU improves the operation of a V.3 gearbox and makes that the replica equals the more expensive replicas and the more sophisticated PTW class replicas. The ASCU system monitors the operation of the replica no matter the speed of squeezing the trigger and is responsible for the full cycle of the piston’s operation, both in the semi-automatic and full automatic firing modes. The piston stops in the starting position after each shot.
The ASCU is equipped with the Low Drain Protection system which is specially designed to secure the lithium-polymer (LiPo) batteries from being damaged.
In case of any emergency, the ASCU stops the firing mode in the replica and, therefore, secures the inner elements from further damage.
The ASCU is easy to install in the replica which is equipped in the V.2 gearbox. Most of the models does not require the modification of the airsoft rifle’s original parts. Yet, in some cases, some minor changes may have to be introduced – thanks to this the installation process will be completed without any problems.
The set includes:
- the replica,
- the magazine,
- a battery,
- a charger,
- a cleaning rod,
Battery included NiCd
rechargeable battery is characterized by high efficiency
current-carrying capacity, but there are disruptive effect on memory.
Should be unloaded and loaded in the full cycle, ie, it is recommended
to fully discharge, and after unloading must charge the battery
immediately without leaving it for a long time in a discharged state. | Yes |
| Product length [cm] | 87.50 |
| Product weight [g] | 2560 |
| Power supply | Electric |
| Material | Metal Plastic |
| Muzzle velocity [FPS] It is the spped of bb, while its leaving the innerbarrel of replica. This speed is measured in FPS (Feet Per Second). 1 FPS = 0,3 m/s 1 J = 99 m/s 1 J = 326,7 FPS | 370 |
| Fire mode | Full-auto Semi-auto |
| Gearbox version Indications v2, v3, v6 does not mean the level of advance, but only shape of gearbox skeleton which was used and selected by the manufacturer depending on the capabilities of the body of the replica. For example, a models of the M4/M16 family, MP5, have a v2 gearbox, while the AK family have gearbox v3. | Gearbox v2 |
| Hop-Up Hop-Up system is used for overclocking bb during the shot (putting it in rotation), through which, it extends its flight path. Acting laws of physics make that bb lift up, while the gravitational force take it down. Appropriate adjustment of Hop-Up, will compensate for these two factors, which result in long and straight flight for longer distance and be greater focus shot (to improve accuracy). | Yes |
| Inner barrel length [mm]. | 390 |